Best Practices for Applying Barcodes - Revision history

Jgreco: Proofread - greco

2021-11-12T18:05:09Z

Proofread - greco

Jvargo at 16:02, 25 March 2016

2016-03-25T16:02:29Z

Jvargo: /* Special Considerations */

2015-09-14T19:19:55Z

Special Considerations

Jvargo: /* About This Page */

2015-09-14T19:10:55Z

About This Page

Jvargo: /* About This Page */

2015-09-14T19:05:36Z

About This Page

Jvargo: Created page with "==About This Page== This page addresses the proper process for securely applying quality-checked pressure-sensitive barcodes (nameplates/labels) in sequential order. A PDF co..."

2015-09-14T17:34:49Z

Created page with "==About This Page== This page addresses the proper process for securely applying quality-checked pressure-sensitive barcodes (nameplates/labels) in sequential order. A PDF co..."

New page

==About This Page==
This page addresses the proper process for securely applying quality-checked pressure-sensitive barcodes (nameplates/labels) in sequential order.

A PDF containing photos and step by step instructions has been linked [[:File:Application Info.pdf|here]]. The instructions below present the same information.

<nowiki>***</nowiki>Following strict application procedures will eliminate 95% of the non-sticking issues.<nowiki>***</nowiki>

==Special Considerations==
*Bond strength increases with time, temperature, and pressure. If you can increase any or all of these, your bond strength will improve.
**Service temperature is the temperature up to which adhesives can maintain bond strength.
**Some adhesives have a service temperature to 450 degrees F (232 degrees C.)
*Small rollers for wallpaper seams, or label squeegees, work the best for getting the adhesive and label to flow evenly across the substrate, forcing the adhesive to bond better.
*MOST IMPORTANT is to ensure you have a clean surface to start. To ensure a strong bond, no dirt or debris should be present. Rubbing Alcohol and a lint free cloth will be best for cleaning.
*Important Storage Information: Pressure-sensitive adhesive used on labels will retain its adhesive properties longer if stored in a cool, dry place (72°F or cooler, less than 50% relative humidity) away from direct heat or sunlight. Do not apply nameplates/labels when temperatures are 50°F or cooler.

==Supplies Needed==
*Your order of quality-checked pressure-sensitive nameplates/labels in sequential order.

*Cleaning solution to clean all surfaces prior to product application

==OVERVIEW: Steps to be Executed==
*Find the best time of day to apply the labels, when the cylinder is not sweating and it is not in direct sunlight.

*Clean the area with isopropyl alcohol and make sure it is dry.

*Apply the label following the instructions on how to properly remove the label from the liner holding it by the edges at top and bottom of label.

*Apply the label to the cylinder and apply even pressure over the entire label. If possible use a label squeegee or wallpaper roller for seams will work the best. This pressure helps to increase the bond strength evenly over the label, reducing flagging.

==STEP 1: Clean Surface==
It is extremely important that application surfaces are properly cleaned prior to product application.

Surfaces may be cleaned with an industrial cleaning solution(which your organization may already be using) or isopropyl alcohol.

All surfaces must be cleaned and completely dried to ensure adequate adhesion.

Plastic surfaces should be rubbed vigorously to remove the potential presence of mold release or silicone.

'''NOTE:''' A permanent bond cannot be achieved if grease, oil, wax, moisture, silicone, mold release or dirt is present on the application surface.

Both new and used equipment surfaces must be cleaned thoroughly prior to application.

==STEP 2: Handle with Care==
Pressure-sensitive adhesive products should be handled only by the edges once the protective liner has been removed from the product.

Do not touch the exposed adhesive after the backing has been removed from the product.

<nowiki>***</nowiki>The pressure sensitive adhesive product should be applied immediately after the liner has been removed.<nowiki>***</nowiki>

[[File:Capture5.PNG|350px]] [[File:Capture.PNG|350px]] [[File:Capture2.PNG|350px]]

==STEP 3: Bond Product==
Apply the pressure-sensitive product firmly to a clean, dry surface.

Do not touch the adhesive backing while applying.

Use firm thumb pressure over the product surface to release the excess air.

Be sure that all edges have a secure bond.

[[File:Capture3.PNG|350px]] [[File:Capture4.PNG|350px]]

@@ Line 6: / Line 6: @@
 '''For information outlining the benefits of using TrackAbout barcode labels, please visit the [[Justification for TrackAbout Barcode Labels]] page.'''
 ==Special Considerations==
@@ Line 66: / Line 68: @@
 [[File:Capture3.PNG|350px]] [[File:Capture4.PNG|350px]]

← Older revision		Revision as of 19:05, 14 September 2015
Line 2:		Line 2:
	This page addresses the proper process for securely applying quality-checked pressure-sensitive barcodes (nameplates/labels) in sequential order.		This page addresses the proper process for securely applying quality-checked pressure-sensitive barcodes (nameplates/labels) in sequential order.

−	~~A PDF containing photos and step by step instructions has been linked~~ [[~~:File:Application Info.pdf\|here~~]]~~. The instructions below present the same information~~.	+	For information outlining the benefits of using TrackAbout barcode labels, please visit the [[Justification for TrackAbout Barcode Labels]] page.

@@ Line 10: / Line 10: @@
 ==Special Considerations==
-*Bond strength increases with time, temperature, and pressure.  If you can increase any or all of these, your bond strength will improve.
+*Bond strength increases with time, temperature, and pressure. If you can increase any or all of these, your bond strength will improve.
 **Service temperature is the temperature up to which adhesives can maintain bond strength.
 **Some adhesives have a service temperature to 450 degrees F (232 degrees C.)
 *Small rollers<sup>1</sup> for wallpaper seams, or label squeegees, work the best for getting the adhesive and label to flow evenly across the substrate, forcing the adhesive to bond better.
-*MOST IMPORTANT is to ensure you have a clean surface to start.  To ensure a strong bond, no dirt or debris should be present.  Rubbing Alcohol and a lint free cloth will be best for cleaning.
+*MOST IMPORTANT is to ensure you have a clean surface to start. To ensure a strong bond, no dirt or debris should be present. Rubbing Alcohol and a lint free cloth will be best for cleaning.
 *Important Storage Information: Pressure-sensitive adhesive used on labels will retain its adhesive properties longer if stored in a cool, dry place (72°F or cooler, less than 50% relative humidity) away from direct heat or sunlight. Do not apply nameplates/labels when temperatures are 50°F or cooler.
@@ Line 60: / Line 60: @@
 ==STEP 3: Bond Product==
 Apply the pressure-sensitive product firmly to a clean, dry surface.
-−
 Do not touch the adhesive backing while applying.

@@ Line 2: / Line 2: @@
 This page addresses the proper process for securely applying quality-checked pressure-sensitive barcodes (nameplates/labels) in sequential order.
-For information outlining the benefits of using TrackAbout barcode labels, please visit the [[Justification for TrackAbout Barcode Labels]] page.
+<nowiki>***</nowiki>Following strict application procedures will eliminate 95% of the non-sticking issues.<nowiki>***</nowiki>
-<nowiki>***</nowiki>Following strict application procedures will eliminate 95% of the non-sticking issues.<nowiki>***</nowiki>
+'''For information outlining the benefits of using TrackAbout barcode labels, please visit the [[Justification for TrackAbout Barcode Labels]] page.'''
 ==Special Considerations==